[. . . ] The seriousness is classified by the following indications.
ENGLISH
WARNING CAUTION
This symbol indicates the possibility of death or serious injury. This symbol indicates the possibility of injury or damage.
n Meanings of symbols used in this manual are as shown below.
Be sure not to do. Be sure to follow the instruction.
WARNING
n Installation
Do not use a defective or underrated circuit breaker. Use this appliance on a dedicated circuit.
· There is risk of fire or electric shock.
For electrical work, contact the dealer, seller, a qualified electrician, or an Authorized Service Center.
· Do not disassemble or repair the product. [. . . ] Indoor Fan Speed Selection Button · To select the desired fan speed in two steps [Low, Mid] 4. Power ON/OFF Button · Operation will start when this button is pressed, and stop when the button is pressed again. Auto Airfloor Direction Control Button (No application) · The horizontal louvers swing up and down. Auto Airflow Direction Control Button · The vertical louvers swing left and right.
12 7 14 3
(Heat pump Model)
1 2 11 12 10 14 3
A/CL
9. Timer Set Button · Each time the button is pressed, the mode is changed in the following process. Time set (1, 2, 3, 4, 5, 6, 7 hours) If you select "0" the off Timer function will be cancelled. Electric heater On/OFF Button(Heat pump & Electric heater product only) 17. ENERGY Saving Operation Button(No application)
16 4 9 13 8 15 6 5
Wireless Remote Control Puts all functions at your fingertips
Handling the remote control
· Aim at the signal receptor on the floor standing type air conditioner when operating. · The remote control signal can be received at a distance of up to about 7meters. · Be sure that there are no obstructions between the remote control and the signal receptor. Press the Soft Dry Operation Button on the remote controller.
A/CL
3
Set the temperature lower than the room temperature. The temperature can be set within a range of 18°C~30°C by 1°C.
To raise the temperature To lower the temperature
During softy Dry Operation
· The indoor fan speed is automatically set to low and can be set fan speed.
12 Floor Standing-Type Air Conditioner
Operating Instructions
ENGLISH
Heating Operation Mode(Heat Pump Model)
1
Press the Start/Stop Button.
2
Select heating Operation. Press the heating Operation Button on the remote controller.
A/CL
3
Set the temperature upper than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C.
To raise the temperature To lower the temperature
4
Set the Fan Speed.
q Each time the Button is pressed, the Fan Speed mode is shifted.
Owner's Manual 13
Operating Instructions
Auto Operation Mode(Cooling Model Only)
1
Press the Start/Stop Button.
2
Select Auto Operation. Press Auto Operation Button.
A/CL
3
Set the temperature upper or lower than the standard temperature. The temperature can be set within a range of by 1 level.
Cold Cool Proper
Warm Hot
(This indication will be shifted to the initial Auto Mode Display state after 4 seconds. )
To raise the temperature. (When you feel too warm or hot)
During Auto Operation
· It is impossible to switch the indoor fan speed because of being already set to the best conditioner by fuzzy rule.
14 Floor Standing-Type Air Conditioner
Operating Instructions
ENGLISH
Electric Heater Operation Mode(Heat pump & Electric heater product only)
1
Press the Start/Stop Button.
2
Select heating Operation by pressing the Opertion Mode Selection button. Press the Heater Operation Button on the remote controller.
A/CL
3
Set the temperature upper than the room temperature. [. . . ] Air conditioner does not operate for about 3 minutes when restarted.
· Check that this is not a damp smell exuded by the walls, carpet, furniture, or cloth items in the room. · Condensation occurs when the airflow from the air conditioner cools the warm room air. · If the airflow begins before its temperature become warm, it will cause an undesired cooling effect. In order to prevent this, the airflow will not begin until it is sufficiently warm. [. . . ]